Asphalt Driveway Paving & Installation Melbourne, FL 32901

Asphalt Paving in Melbourne, FL (32901) · Local Professionals

Palm Bay Asphalt Paving · Fast response in Melbourne and the Palm Bay area · Free estimate 24h

✅ Written Estimates & Tonnage Specs 🛡️ Fully Insured 💸 Free Quote 24h 🕐 Mon-Sat 7am-6pm

+31Verified Reviews

15Years in Business

4.9 ★Google Rating

24/7Available

Melbourne's river neighborhoods and busy retail corridors run on driveways and parking lots that are aging faster than most homeowners expect. Your driveway crosses a swale on a culvert pipe, sits on fine gray sand, and faces relentless sun, salt air, and more than 50 inches of rain every summer. That combination breaks asphalt in ways that northern climates never see.

Palm Bay Asphalt Paving has served Melbourne and the surrounding Space Coast since 2011. We know the sand base, the drainage challenges, and the storm damage that hits this area every season. When your driveway settles at the edges, when standing water softens the base after a tropical downpour, or when potholes and raveling asphalt become a trip hazard, we show up local, measure the job properly, and tell you honestly whether to patch, resurface, or replace.

Asphalt Paving in Melbourne (32901)

Melbourne's housing stock tells the story. Thousands of 1980s through 2020s concrete block and stucco ranches sit on quarter-acre lots platted in the 1960s and 70s, each driveway crossing a culvert swale to reach the street. Bayside Lakes, Waterstone, and the southeast master-planned communities added wider driveways that are all aging together now. The northwest and southwest still see new homes going up on wooded lots and freshly cut streets. Eau Gallie and the river neighborhoods carry older 1920s through 1950s cottages and mid-century ranches whose driveways have seen decades of use.

The soil here is fine gray sand over a high water table, with pockets of muck and coquina rock. We build bases from compacted limerock or crushed concrete. The real enemies are water and heat. Summer thunderstorms dump inches of rain in hours. Hurricanes like Milton and Ian flood swales and undercut drive edges. The sun oxidizes asphalt fast, and there is no freeze to crack it, so the failures you see are edge settlement, softened bases, surface raveling, potholes, and broken pavement at the corners where sand was never properly confined or compacted. We have been solving these problems on Melbourne driveways and parking lots since 2011.

Our services in Melbourne

Asphalt Driveway Paving & Installation in Melbourne · New hot-mix driveways built on a compacted sand subgrade and a limerock or…
Driveway Repair in Melbourne · Sunken aprons; crumbling edges; edges washed out by storm water and sections…
Pothole Repair & Asphalt Patching in Melbourne · Potholes cut square then tack-coated and filled with compacted hot mix.
Asphalt Resurfacing & Overlay in Melbourne · A new 1.5-2 inch compacted surface course over a structurally sound driveway…
Asphalt Milling & Removal in Melbourne · Mill-and-pave; full-depth reclamation or complete tear-out with haul-away.
Driveway Replacement in Melbourne · When alligator cracking runs section to section the base underneath is gone and…
Parking Lot Paving & Construction in Melbourne · New parking lots and expansions for retail; HOA; church…
Parking Lot Repair & Resurfacing in Melbourne · Potholes; failed sections; storm inlet rebuilds and full overlays for…
Recycled Asphalt & Millings Driveways in Melbourne · Compacted asphalt millings make a solid budget-smart surface for long drives…
Tar & Chip Driveways in Melbourne · Tar and chip, liquid asphalt with rolled stone chips…
Gravel Driveway Installation & Grading in Melbourne · New gravel drives built in proper lifts of limerock or crushed concrete over…
Private Road & HOA Paving in Melbourne · Private lanes; HOA and gated-community streets…
Driveway Extensions, Widening & Aprons in Melbourne · Add a parking pad for the boat or the third car…
Sports Court & Path Paving in Melbourne · Backyard basketball courts; tennis and pickleball bases…

How a Job Works in Melbourne

You call us at (321) 237-3624 and describe what you see. We schedule a free on-site visit. We measure your driveway or lot, look at the base, check the drainage and pitch, and tell you what is failing and why. If your driveway is settling or has soft spots, we probe the base. If you have potholes or alligator cracking across thirty or forty percent of the surface, we explain why a patch throws money away and resurfacing or replacement is the right call. We give you a written estimate with square footage, thickness, and tonnage so you know exactly what you are paying for.

On the day of the work, our crew arrives early to avoid afternoon thunderstorms. We mill or remove old asphalt if needed, prepare and compact the base, lay new asphalt to the thickness specified in your estimate, and roll it smooth. If your driveway runs tight between a house and a swale or a neighbor's property, we have the experience to work in tight spaces. If you are in an HOA community, we coordinate with your architectural standards. We leave your property clean and walk through the finished job with you.

A new asphalt driveway in Melbourne starts at around $6 per square foot, depending on the base condition and thickness. Resurfacing an existing driveway runs from about $4 per square foot if the base is sound. Pothole and patch repairs start at $450 and are the right choice if you have only a few isolated failures. A full driveway replacement, when the base is gone or the settlement is too severe to fix, starts at around $7 per square foot. Parking lot work varies widely by size and condition, from spot repairs at $650 to full resurfacing or new construction, and we give free commercial estimates. The biggest cost factors are square footage, base condition, thickness (which we specify in writing), access for the paver and roller, and whether we need to mill or remove old pavement first. Call us at (321) 237-3624 for a free estimate. We measure on site, quote in writing, and never surprise you.

✅ Written Estimates & Tonnage Specs, fully insured for work in Melbourne and nearby areas.

My driveway has settled where it crosses the swale culvert. Is that fixable, or do I need a whole new driveway?

Settlement at the swale crossing is one of the most common failures we see in Melbourne. If the drop is less than half an inch and the asphalt is not cracked badly, we can often build up and level the low spot with a resurfacing overlay. If the settlement is more than an inch or the asphalt around it is heavily cracked, the base has likely shifted or compacted unevenly, and replacement is usually the better long-term fix. We probe and measure on site to give you an honest answer.

My parking lot flooded after the last storm and now there are soft spots where the water sits. Can I just patch it?

Soft spots mean the base is holding water because the pitch or the drainage has failed. A patch will not fix that, and the water will keep softening the base underneath. We assess the drainage, check the slope, and often recommend resurfacing or overlay to restore proper pitch and shed water away from the pavement. If the base is truly compromised, we may need to mill, regrade, and rebuild. Call us at (321) 237-3624 and we will look at it for free.

What does asphalt paving cost in Melbourne, and what affects the price?

Driveway paving runs from about $6 per square foot for new installation and $4 per square foot for resurfacing, but those are starting points. The real costs depend on the size of the job, the condition of the base, whether we need to mill or remove old pavement, access for equipment, and the thickness we specify for your soil and climate. A 500-square-foot driveway might run $3,000 to $3,500 for resurfacing or $3,000 to $3,500 for new paving depending on the base. We always give a written estimate with tonnage and thickness before we start.

Do I need a permit for driveway paving in Melbourne, and who issues it?

Permits for driveway aprons, curb cuts, and right-of-way work vary by municipality across the Palm Bay area. Melbourne and the surrounding cities each have their own rules. We help you navigate the local permitting process, but you should verify requirements with your city or county building department. The City of Melbourne's official site at https://www.brevardfl.gov can direct you to the right office. If you are in an HOA community, architectural approval is also required.

I live in an HOA community. Can I just hire you to pave my driveway, or do I need approval first?

Most HOA communities in the greater Melbourne area have architectural standards that govern driveway material, color, and extensions. You will need to submit your paving plan to your HOA architectural committee and get written approval before we begin work. We can help you understand what the work will look like and what documentation the HOA might ask for. Always check your CC&Rs and get approval in writing first, because the HOA can require you to remove unpermitted work at your own cost.

Are you insured for the work you do at my Melbourne property?

Yes. We are fully insured with general liability and workers' compensation coverage for all paving work. Any contractor working on your property should carry current insurance, and you should ask to see proof before work begins. We can provide our insurance information on request.

I just had new asphalt paving installed. When can I seal it, and how do I maintain it?

New asphalt must cure for at least six to twelve months before any sealcoating. During that cure period, the asphalt is still settling and the binder is hardening. Sealing too early traps moisture and can cause premature failure. After twelve months, regular maintenance like crack filling and sealcoating every two to three years will extend the life of your pavement. In Melbourne, the intense sun and salt air mean asphalt oxidizes faster than in other climates, so staying on top of maintenance pays off.